![]() If you have any questions or trouble contact Red Lion Technical Support by clicking here or calling 1-87.Federal Way city officials say they feel they haven’t been given clarity or updates on the project, let alone any idea of when the hotel will open. Red Lion standard product warranty applies. The use of this document is at your own risk. Red Lion is not responsible for any damage to equipment or connected systems. Red Lion makes no representation about specific knowledge of the customer's system or the specific performance of the system. It is the customer's responsibility to review the advice provided herein and its applicability to the system. showing CR3000 HMI sending data via Tag1 and receiving data via Tag2 showing DA50A sending data via Tag 2 and Receiving data via Tag 1įigure 15. Flexedge DA50A is subscribed to this topic via subscription topic dev2 in order to receive this data in Tag 1 under Tag set 2 in Crimson 3.2 database.įigure 14. This data is being published by setting up publication topic dev1 under Tag set 1 in Crimson 3.2 database while CR3000 is subscribing to topic via subscription topic dev1 in order to receive this data in Tag 2 under Tag set 2 in Crimson 3.1 database.ĭata from Tag 1 on the CR3000 HMI is manually entered from touch screen which is then published via publication Topic dev2 under Tag set 1 in Crimson 3.1 database. This is done via display pages -> Pages -> Global Actions - > On Tick and by doing Tag 2 . Tag 2 is updating once a second in DA50A unit. You should get the message The Mosquitto Broker service was started successfully. Start the Mosquitto service by running the command: net start mosquitto, refer to Figure 13. Navigate to the Mosquitto root folder, such as C:\Program Files (x86)\mosquito by doing CD C:\Program Files (x86)\mosquittoģ. Note: You absolutely need to make sure you run CMD as administrator and make sure you don’t have more than one instance of CMD open.Ģ. Start the broker, referring to Figure 12, open a command prompt and make sure you run as administrator. ![]() Go to display pages -> Pages -> Global actions -> On Tick and enter Tag2 to get Tag 2 to increment every second as shown in Figure 11ĭownload and install Mosquitto from Running Mosquittoġ. Create two internal tags - Tag1 and Tag2 as shown in Figure 8.ĥ. Go to communications-> Connector -> Generic MQTT -> service tab and set it up as seen in Figure 7.ģ. Go to Device Configuration -> system configuration -> Network -> Interfaces -> Ethernet 1 and set up the IP Address as shown in Figure 6.Ģ. Create two internal tags - Tag1 and Tag2 as shown in Figure 3.įigure 5 Crimson 3.2 DA50A Configuration:ġ. Go to Connectors -> Generic MQTT -> service tab and set it up as shown in Figure 2.ģ. Go to Communications -> Network -> Ethernet 1 and set up the IP Address of CR3000 HMI as shown in Figure 1.Ģ. IP Address of Mosquitto Broker running on Laptop: 192.168.0.85 Crimson 3.1 CR3000 Configuration:ġ. Two Red Lion devices used in this example are DA50A and CR3000 HMI ![]() This tech note will talk about how to use Generic MQTT to get two Red Lion devices to communicate. They are Modbus TCP/IP, OPC Proxy TCP/IP Master, OPC UA and Generic MQTT. There are four different methods to get two Red Lion devices to communicate. ![]() This document describes setting up a connection that allows two Red Lion devices to communicate via Generic MQTT ProductsĭA10, DA30, Fle圎dge(DA50D, DA70D, DA50A and DA70A) and CR3000 or Graphite HMI/Graphite Edge Controller Use CaseĮstablishing Communication between two Red Lion devices via Generic MQTT using Mosquitto Broker. ![]()
0 Comments
Leave a Reply. |